ok here is some help for those of you that want to try this!<img src=icon_smile_shock.gif border=0 align=middle>
Firstly we have to take off the dash!
1. Take out the following. Radio, drawer (under radio), passenger side air vent.
2. Unscrew the centre consol, two underneath, one on each side one where the drawer was. Then take off the triangle with the hazard warning lights two screws are here.
3. Then unscrew the rev counter and the clock. Pull the centre consol off.
4. unscrew the four screws under the steering column and lift off and put to one side the Speedo. Remember that the Speedo will still be plugged in so be careful.
****************************ADDED***************** ***********
on the right hand side of the steering coloumn is another screw holding the top of the dash to the lower section you need to go straigh in towards the front of the car. sorry for any confusion with this one!:embarasse
****************************ADDED***************** ***********
5. where the air vent was take out the large screw inside the dash.
6 now its time to lift the dash up but remember if you don’t have the sound upgrade to disconnect the speakers! Lift up the front and pull out
Now that you have the dash out you can get the bass bins and speakers ready.
Put the bass bins into place and secure them down. You don’t want any rattles!
Now wire up your new speakers and place them into the bass bins (forgot to mention before you get to this stage make sure that your speakers fit in to the boxes!). there is a small gap when you place the speakers in to feed the wire out side of the box plus on the side of the boxes there are some clips to hold the wire.
Now plug the stereo in and test to see if they work. If you installed to bass bins for the first time you will notice the difference! If everything works screw down the speakers and make sure that all cables are secure!
Now when fitting the dash back on you will see 3 clips on the front just below the window. I think its best to position the middle one with the hole on the front of the dash then push down and forward if all has worked the dash should be secure! Now you have to screw every back in to place. Take your time as no screws should be left over and as I said before you don’t want any rattles!
Good luck!
Michael Vermaak
********************ADDED********************
to attach the base bins you need
4 x Q0001881V000000000 DG40 x 16z screw
which is the same screw as the lower dash
and 2 6m nuts
2 x Q0001891V000000000 6m nut
to attch the speakers to the bin use the screws provided in the kit or
8 x Q0001880V000000000 K35 x 20 screw
THANKS TO RADON FOR THESE PART NUMBERS!!!!:shade:
********************ADDED********************
Firstly we have to take off the dash!
1. Take out the following. Radio, drawer (under radio), passenger side air vent.
2. Unscrew the centre consol, two underneath, one on each side one where the drawer was. Then take off the triangle with the hazard warning lights two screws are here.
3. Then unscrew the rev counter and the clock. Pull the centre consol off.
4. unscrew the four screws under the steering column and lift off and put to one side the Speedo. Remember that the Speedo will still be plugged in so be careful.
****************************ADDED***************** ***********
on the right hand side of the steering coloumn is another screw holding the top of the dash to the lower section you need to go straigh in towards the front of the car. sorry for any confusion with this one!:embarasse
****************************ADDED***************** ***********
5. where the air vent was take out the large screw inside the dash.
6 now its time to lift the dash up but remember if you don’t have the sound upgrade to disconnect the speakers! Lift up the front and pull out
Now that you have the dash out you can get the bass bins and speakers ready.
Put the bass bins into place and secure them down. You don’t want any rattles!
Now wire up your new speakers and place them into the bass bins (forgot to mention before you get to this stage make sure that your speakers fit in to the boxes!). there is a small gap when you place the speakers in to feed the wire out side of the box plus on the side of the boxes there are some clips to hold the wire.
Now plug the stereo in and test to see if they work. If you installed to bass bins for the first time you will notice the difference! If everything works screw down the speakers and make sure that all cables are secure!
Now when fitting the dash back on you will see 3 clips on the front just below the window. I think its best to position the middle one with the hole on the front of the dash then push down and forward if all has worked the dash should be secure! Now you have to screw every back in to place. Take your time as no screws should be left over and as I said before you don’t want any rattles!
Good luck!
Michael Vermaak
********************ADDED********************
to attach the base bins you need
4 x Q0001881V000000000 DG40 x 16z screw
which is the same screw as the lower dash
and 2 6m nuts
2 x Q0001891V000000000 6m nut
to attch the speakers to the bin use the screws provided in the kit or
8 x Q0001880V000000000 K35 x 20 screw
THANKS TO RADON FOR THESE PART NUMBERS!!!!:shade:
********************ADDED********************
Comment